Search:

Type: Posts; User: michael3130

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    11
    Views
    3,897

    I would try a different way. Kep your...

    I would try a different way. Kep your relationship of thickness but reather than using the cutout method, in the assmbly, use the profile of the ring and do a revolve cut round the gasket. You'll...
  2. Replies
    2
    Views
    2,807

    I disagree with most of what you are saying and I...

    I disagree with most of what you are saying and I believe it is down to your use of the software, just giving an honest opinion. I've used SW since 99 and it is reliable and I've always been able to...
  3. Replies
    5
    Views
    2,887

    you could upload the file to Dropbox and post a...

    you could upload the file to Dropbox and post a link to it.
  4. Replies
    35
    Views
    114,496

    Michaelpaul has pretty much summed up my feelings...

    Michaelpaul has pretty much summed up my feelings too.
  5. Replies
    35
    Views
    114,496

    I agree with Wogz. I'm currently using both Creo...

    I agree with Wogz. I'm currently using both Creo 2 and SW on a daily basis and an equal number of hours per day so I feel I can be justified in giving an opinion and comparing the 2 packages. I...
  6. We had a guy in our office yesterday who is now...

    We had a guy in our office yesterday who is now trying to sort our problems with Creo 2, mainly the slowness of many operations. It's taking nearly 5 minutes to open a 400 part assembly on one...
  7. Replies
    2
    Views
    5,509

    I've been using creo 2.0 and SW 2010 an eequal...

    I've been using creo 2.0 and SW 2010 an eequal amount over the past 4 months and I would now prefer to use SW. I know we are having issues with our setup on Creo which is slowing things down but...
  8. Replies
    1
    Views
    4,278

    I'm not sure if SW2006 has pack and go, I use...

    I'm not sure if SW2006 has pack and go, I use 2010. Basically pack and go collects all the files in that model even if they are in different folders and either puts them into a new folder with all...
  9. Replies
    3
    Views
    2,019

    See attached image of what I was trying to...

    See attached image of what I was trying to explain.
  10. Replies
    3
    Views
    2,019

    I think it may actually be quite a simple bit of...

    I think it may actually be quite a simple bit of modelling. Imagine the basic revolve, the extend the skirt of the revolve. Ok, now looking from above, cut through the revolve with the profile that...
  11. I do as srieger does and it works well, this...

    I do as srieger does and it works well, this method is used throughout our group of companies. Also do as kk_designer says and check units
  12. Replies
    26
    Views
    15,873

    Maybe hate is a strong word but the change over...

    Maybe hate is a strong word but the change over to Creo 2 has caused problems and reduced my productivity so that's the way I felt at the time. I have always loved using solid modelling packages...
  13. Replies
    26
    Views
    15,873

    Thanks for that Krow, I'll try it. I am finding...

    Thanks for that Krow, I'll try it. I am finding my way now and becoming slicker at finding my way through. It just feels like they have taken the ribbon route to be like everyone else and...
  14. Replies
    26
    Views
    15,873

    Thanks Volunteer. That's what I'm worried about,...

    Thanks Volunteer. That's what I'm worried about, 5 months down the line and still hunting for basic commands. I've never moved to a newer version of a software ppackage and felt so uncomfortable...
  15. Replies
    26
    Views
    15,873

    Hating Creo 2

    I've switched over to Creo 2 a week ago and so far I hate it . It feels like everything I do is now more complicated and takes extra clicks to do. A few times I've taken that long trying to find an...
  16. Replies
    2
    Views
    1,890

    That's what I thought, something graphics...

    That's what I thought, something graphics related. The machines were specced for Creo 2 so hopefully any issues will disappear. It's not a big hassle, just something I didn't expect and haven't...
  17. Replies
    2
    Views
    1,890

    Weird Datum Views

    Hi,

    My datums in sketch mode are messing about.

    If I look normally at the sketch, sometimes the right and top datum lines go haywire, they should be horizontal aand vertical but go off at funny...
  18. Replies
    2
    Views
    2,748

    Hi, any chance you could upload the part as an...

    Hi, any chance you could upload the part as an IGES file. I'm using ProE in work but can hopefully tell from looking at the geometry why it's not converting.
    Thanks
    Michael
  19. Replies
    18
    Views
    4,356

    Things are hectic, busier than ever before. Into...

    Things are hectic, busier than ever before. Into production this week with the new line of heaters, tempers are fraying and everyones on edge but if it all went smoothly it would be no fun.


    Hope...
  20. Replies
    18
    Views
    4,356

    Well Gehad, how you getting on with the hairbrush...

    Well Gehad, how you getting on with the hairbrush modelling now??? ;)
  21. Replies
    5
    Views
    5,422

    I downloaded a free program called Bullzip and...

    I downloaded a free program called Bullzip and then print to PDF, it gets round that problem.
  22. Replies
    14
    Views
    8,592

    Eagleeye. people aren't here to do the work for...

    Eagleeye. people aren't here to do the work for you, just provide a bit of guidance to steer you in the right direction, maybe a thank you to s_pme20 would be more appropriate and beneficial than...
  23. Replies
    14
    Views
    8,712

    I haven't posted in a while but I'll put my...

    I haven't posted in a while but I'll put my thoughts in anyway.


    Personally I don't see any harm in knowing a bit about what other people do outside of ProE, makes them real people rather than...
  24. Replies
    32
    Views
    25,086

    All the groups in our company are due to make the...

    All the groups in our company are due to make the change from WF4 to Creo in the new year. I'm sure there'll be a lot of mixed opinions but no matter what we'll have to deal with it and learn it!
  25. Replies
    21
    Views
    7,926

    In your config files, look at the...

    In your config files, look at the rename_drawings_with_object. Set to both and when you save the part or the asssembly, the associated drawing will save a copy too. The links should update as well.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4