Search:

Type: Posts; User: annad_m_s

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    2,593

    CAM surface definintion

    I am trying a design a Cycloidal drive mechanism wherein I am defining a couple of CAM joints. However, when I try to select the cycloidal surface as one the cam surfaces, it seems Creo is making...
  2. Replies
    4
    Views
    849

    Yes I agree that the shape of a spline can be...

    Yes I agree that the shape of a spline can be controlled by switching to control polygon mode. However, any strong dimension used to define the spline would be lost once you switch this mode. In the...
  3. Replies
    4
    Views
    849

    Splines in sketch environment

    Please see the Solidworks tutorial video here https://www.youtube.com/watch?v=fmIgJp6LyCo.

    Is it possible to control the shape of the splines the way it is done using Solidworks in Creo without...
  4. Replies
    2
    Views
    2,656

    Before you start animation you need to have the...

    Before you start animation you need to have the following three parts in your assembly and in the same order:
    1. A carrier
    2. Central Fixed gear
    3. Rotating cum revolving gear.

    The carrier part...
  5. Replies
    7
    Views
    3,354

    Dear Srini, Can you re-upload the attachment...

    Dear Srini,

    Can you re-upload the attachment please? The above given link is no more valid now.
  6. Replies
    14
    Views
    7,459

    Please see my earlier post on the subject here:...

    Please see my earlier post on the subject here: http://www.mcadcentral.com/creo-modeling/28238-closed-helical-spring-using-helical-sweep.html
  7. Replies
    3
    Views
    4,779

    I have tried the above mentioned method to report...

    I have tried the above mentioned method to report the consolidated mass of each item in the BOM table. I am partially successful in my attempt. The following are the hurdles I am facing
    1. The...
  8. You can create a sectional view in two ways: 1....

    You can create a sectional view in two ways:
    1. Define the cross section in the assembly model and then select the same while detailing.
    2. Create a new cross section within the drawing environment...
  9. Thread: creo project

    by annad_m_s
    Replies
    1
    Views
    729

    Use Variable section sweep and trajpar in the...

    Use Variable section sweep and trajpar in the equations
  10. Display of Notebook declared parameters in drawing

    I have created the models of Worm and Worm wheel using parameters and relations defined in a notebook (which used to be known as Layout earlier). I am unable to use these parameters in the drawings...
  11. Replies
    1
    Views
    695

    Set default_font option under Drawing properties...

    Set default_font option under Drawing properties to ISOCPEUR font. That should solve your problem. At least it is working for me!
  12. Replies
    3
    Views
    882

    I thank you Tobias wholeheartedly for taking all...

    I thank you Tobias wholeheartedly for taking all the trouble to answer my query. Unfortunately I do not have the required license for ISDX:(. Hence, I need to be satisfied with whatever available...
  13. Replies
    6
    Views
    1,905

    I found out a video tutorial in Youtube wherein a...

    I found out a video tutorial in Youtube wherein a cheese is modeled with random pores. You may find it useful:https://www.youtube.com/watch?v=i2UNSJVbEXo
  14. Replies
    4
    Views
    1,037

    You need to create the trajectory with 5 segments...

    You need to create the trajectory with 5 segments
    1. First and the last segments: corresponds to the closed coils at the end
    2. Second and the last but segments: corresponds to transition of pitch...
  15. Replies
    3
    Views
    882

    Conic surface and n-sided patch

    There used be an option to create boundary blended surface with more than 4 boundaries using Conic Surface and n-sided patch option in earlier version of Creo and Pro/e. However, I could not see such...
  16. Replies
    3
    Views
    1,084

    Hi, I had a similar requirement some time back...

    Hi,

    I had a similar requirement some time back and I could do it by superimposing two views on one another. I am not sure whether this the best practice or not. Nevertheless, I got the desired...
  17. Datum Points on Self intersecting curves

    I need to place a datum point on the point of intersection of a self intersecting curve. The image of the curve drawn in Creo using equation is attached. I am unable to pick such points with...
  18. Replies
    4
    Views
    1,535

    Hi Dross, I have a set of parameters which get...

    Hi Dross,

    I have a set of parameters which get filled up in the revision table automatically. As of now there are 3 rows in that table and in case the revision status goes beyond 2 (Revision...
  19. Replies
    4
    Views
    1,535

    The purpose of asking this question is to keep...

    The purpose of asking this question is to keep adding the rows of Revision History table in a drawing. To start with I may have 3 rows; but when more than 3 revisions done, I need to keep track of...
  20. Replies
    4
    Views
    1,535

    No. of rows in a table

    Is there a method to control the number of rows in a table, say through a parameter?
  21. Replies
    7
    Views
    4,149

    Embedded picture in drawing format

    We had created the drawing format with our company logo embedded in it. It was clearly visible in WF 5.0. But after upgrading to Creo 2.0, this picture has become invisible. However, it gets...
  22. Replies
    2
    Views
    2,433

    Thanks Doug for your suggestion. I tried to bend...

    Thanks Doug for your suggestion. I tried to bend the square tube using Spinal Bend option but in vain. There were all sorts of errors- Self intersecting geometry, Surfaces getting inverted etc.
  23. Replies
    2
    Views
    2,433

    Bending of Square Tube

    Is it possible to bend a square tube in the way shown in this video using Solidworks? SolidWorks Bending a Square Tube - YouTube.
    I am unable to reduce the "X" distance to zero in Pro E WF 5.0 and...
  24. Replies
    6
    Views
    2,339

    There is no direct method to sketch an elliptical...

    There is no direct method to sketch an elliptical arc within sketcher environment. However, you can create an elliptical curve (either full or partial) using parametric equations.
  25. Thread: rotating leg

    by annad_m_s
    Replies
    2
    Views
    1,040

    It is very much possible to constrain a rotating...

    It is very much possible to constrain a rotating member within a certain envelope. You need to use pin joint with the proper definition of "Rotation Axis" option.
Results 1 to 25 of 27
Page 1 of 2 1 2