Search:

Type: Posts; User: dross

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    1,806

    Those are the offset section lines to show where...

    Those are the offset section lines to show where the section is.
    If a planar section, those lines would not be there.
  2. Replies
    12
    Views
    7,891

    Bestellen again copies an old post and seems to...

    Bestellen again copies an old post and seems to be here for spamming or some other nefarious purpose.
  3. If the views were created in the model while the...

    If the views were created in the model while the model is exploded, then the explode state saves with the view state.
    IF not, Then I'm not of any help on this one.
  4. Replies
    17
    Views
    17,888

    There is no "edit" in Creo 3. You copied what...

    There is no "edit" in Creo 3.

    You copied what was posted for an earlier version of Creo.
  5. Thread: Overall speed

    by dross
    Replies
    5
    Views
    1,152

    A couple of config options that help: ...

    A couple of config options that help:

    regen_int_mdls_on_retr no
    disable_search_path_check yes
  6. Replies
    4
    Views
    971

    Toony, YOu need to get familiar with your...

    Toony,

    YOu need to get familiar with your Config.pro
    All of the questions you posted here and elsewhere are related to config options.
    The dual dimensioning is in the detail options of the...
  7. Replies
    7
    Views
    2,603

    You were in Louisiana?

    You were in Louisiana?
  8. Replies
    3
    Views
    1,714

    Set the config option save_object_in_current to...

    Set the config option save_object_in_current to no.
  9. Replies
    4
    Views
    2,207

    Each step of your staircase is a part that is...

    Each step of your staircase is a part that is likely identical. Reference pattern this part based upon the helical sweep pattern in the assembly.
  10. Replies
    7
    Views
    2,603

    Between Idaho and Maine?

    Between Idaho and Maine?
  11. Replies
    6
    Views
    2,154

    Only the brave and\or dumb. First release...

    Only the brave and\or dumb.
    First release software always has lots of bugs, which I don't have time to deal with.
  12. Thread: Thinking in 3D

    by dross
    Replies
    9
    Views
    3,656

    Pre-Wildfire would have been version 2001. I...

    Pre-Wildfire would have been version 2001. I liked it too!
  13. Replies
    1
    Views
    4,802

    There are different versions of the license...

    There are different versions of the license server software, perhaps yours is the wrong one for your configuration.
    Some are not compatible with XP.
    You may need to run a different operating system...
  14. Replies
    3
    Views
    1,513

    I never use the notes that Creo provides. They...

    I never use the notes that Creo provides.
    They are too long and contain unesecessary information.
  15. Replies
    11
    Views
    14,502

    I use the analysis all the time. The key is to...

    I use the analysis all the time.
    The key is to use the correct filters (usually surface or axis), and to use a projection feature if needed.
    Takes a lot less time than creating a drawing.
  16. Thread: Thinking in 3D

    by dross
    Replies
    9
    Views
    3,656

    It didn't click for me until solids were...

    It didn't click for me until solids were available. Wireframe was very confusing.
  17. Replies
    3
    Views
    3,614

    I hope they get this fixed in Creo 4. There...

    I hope they get this fixed in Creo 4.
    There should be no reason for flexible dimensions to break the repeat region.
  18. Thread: Project Surface

    by dross
    Replies
    13
    Views
    3,566

    I wish that I could go back to WF4! After several...

    I wish that I could go back to WF4! After several years of using Creo 2, 3, and now 4, WF4 is superior in most instances.
    There are some nice features in Creo, but not enough to make up for the...
  19. No grudge. You didn't read the article I...

    No grudge.

    You didn't read the article I posted a link to, did you?
    What do you think they used in 1986 to NC the boat prop? It was a CAD/CAM system. Does not say which one, and does not matter....
  20. You are now simply trying to cover over with BS....

    You are now simply trying to cover over with BS. You said "The first NC programmed boat prop was done w/ Pro/ENGINEER using a trajpar graph in 1992 by a titanium mill house in Washington State."
    ...
  21. Come on Bart, get your facts straight!! See...

    Come on Bart, get your facts straight!!
    See linked article, boat props were being machined on NC machines beginning in the 1970's or 80's.
    ...
  22. Replies
    4
    Views
    1,609

    If the parts are not in an assembly, then I would...

    If the parts are not in an assembly, then I would add them to one just so that you can do as you want and show them in the repeat region.
    As individual parts that are not in an assembly, I don't see...
  23. I looked through there and did not find any...

    I looked through there and did not find any reference to undocking the placement panel.
    How do you do it? Nevermind, figured it out.
    I did what you did, tried clicking on where it was, and it...
  24. Replies
    8
    Views
    5,485

    Change your tab to "History" instead of...

    Change your tab to "History" instead of "Attributes" and then select "ID"
  25. Replies
    9
    Views
    2,319

    You would need to set this up in your pen file...

    You would need to set this up in your pen file (table.pnt) probably to a thickness of 0 and a light color
    It also might be done as you have suggested with a dotted line with large dot spacing.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4